Benchmarking (python vs. c++ using BLAS) and (numpy)

UPDATE (30.07.2014):

I re-run the the benchmark on our new HPC. Both the hardware as well as the software stack changed from the setup in the original answer.

I put the results in a google spreadsheet (contains also the results from the original answer).

Hardware

Our HPC has two different nodes one with Intel Sandy Bridge CPUs and one with the newer Ivy Bridge CPUs:

Sandy (MKL, OpenBLAS, ATLAS):

• CPU: 2 x 16 Intel(R) Xeon(R) E2560 Sandy Bridge @ 2.00GHz (16 Cores)
• RAM: 64 GB

Ivy (MKL, OpenBLAS, ATLAS):

• CPU: 2 x 20 Intel(R) Xeon(R) E2680 V2 Ivy Bridge @ 2.80GHz (20 Cores, with HT = 40 Cores)
• RAM: 256 GB

Software

The software stack is for both nodes the sam. Instead of GotoBLAS2, OpenBLAS is used and there is also a multi-threaded ATLAS BLAS that is set to 8 threads (hardcoded).

• OS: Suse
• Intel Compiler: ictce-5.3.0
• Numpy: 1.8.0
• OpenBLAS: 0.2.6
• ATLAS:: 3.8.4

Dot-Product Benchmark

Benchmark-code is the same as below. However for the new machines I also ran the benchmark for matrix sizes 5000 and 8000.
The table below includes the benchmark results from the original answer (renamed: MKL --> Nehalem MKL, Netlib Blas --> Nehalem Netlib BLAS, etc)

Single threaded performance:

Multi threaded performance (8 threads):

Threads vs Matrix size (Ivy Bridge MKL):

Benchmark Suite

Single threaded performance:

Multi threaded (8 threads) performance:

Conclusion

The new benchmark results are similar to the ones in the original answer. OpenBLAS and MKL perform on the same level, with the exception of Eigenvalue test. The Eigenvalue test performs only reasonably well on OpenBLAS in single threaded mode. In multi-threaded mode the performance is worse.

The "Matrix size vs threads chart" also show that although MKL as well as OpenBLAS generally scale well with number of cores/threads,it depends on the size of the matrix. For small matrices adding more cores won't improve performance very much.

There is also approximately 30% performance increase from Sandy Bridge to Ivy Bridge which might be either due to higher clock rate (+ 0.8 Ghz) and/or better architecture.

---

Original Answer (04.10.2011):

Some time ago I had to optimize some linear algebra calculations/algorithms which were written in python using numpy and BLAS so I benchmarked/tested different numpy/BLAS configurations.

Specifically I tested:

• Numpy with ATLAS
• Numpy with GotoBlas2 (1.13)
• Numpy with MKL (11.1/073)
• Numpy with Accelerate Framework (Mac OS X)

I did run two different benchmarks:

1. simple dot product of matrices with different sizes
2. Benchmark suite which can be found here.

Here are my results:

Machines

Linux (MKL, ATLAS, No-MKL, GotoBlas2):

• OS: Ubuntu Lucid 10.4 64 Bit.
• CPU: 2 x 4 Intel(R) Xeon(R) E5504 @ 2.00GHz (8 Cores)
• RAM: 24 GB
• Intel Compiler: 11.1/073
• Scipy: 0.8
• Numpy: 1.5

Mac Book Pro (Accelerate Framework):

• OS: Mac OS X Snow Leopard (10.6)
• CPU: 1 Intel Core 2 Duo 2.93 Ghz (2 Cores)
• RAM: 4 GB
• Scipy: 0.7
• Numpy: 1.3

Mac Server (Accelerate Framework):

• OS: Mac OS X Snow Leopard Server (10.6)
• CPU: 4 X Intel(R) Xeon(R) E5520 @ 2.26 Ghz (8 Cores)
• RAM: 4 GB
• Scipy: 0.8
• Numpy: 1.5.1

Dot product benchmark

Code:

import numpy as np
a = np.random.random_sample((size,size))
b = np.random.random_sample((size,size))
%timeit np.dot(a,b)

Results:

    System        |  size = 1000  | size = 2000 | size = 3000 |
netlib BLAS       |  1350 ms      |   10900 ms  |  39200 ms   |    
ATLAS (1 CPU)     |   314 ms      |    2560 ms  |   8700 ms   |     
MKL (1 CPUs)      |   268 ms      |    2110 ms  |   7120 ms   |
MKL (2 CPUs)      |    -          |       -     |   3660 ms   |
MKL (8 CPUs)      |    39 ms      |     319 ms  |   1000 ms   |
GotoBlas2 (1 CPU) |   266 ms      |    2100 ms  |   7280 ms   |
GotoBlas2 (2 CPUs)|   139 ms      |    1009 ms  |   3690 ms   |
GotoBlas2 (8 CPUs)|    54 ms      |     389 ms  |   1250 ms   |
Mac OS X (1 CPU)  |   143 ms      |    1060 ms  |   3605 ms   |
Mac Server (1 CPU)|    92 ms      |     714 ms  |   2130 ms   |

Benchmark Suite

Code:
For additional information about the benchmark suite see here.

Results:

    System        | eigenvalues   |    svd   |   det  |   inv   |   dot   |
netlib BLAS       |  1688 ms      | 13102 ms | 438 ms | 2155 ms | 3522 ms |
ATLAS (1 CPU)     |   1210 ms     |  5897 ms | 170 ms |  560 ms |  893 ms |
MKL (1 CPUs)      |   691 ms      |  4475 ms | 141 ms |  450 ms |  736 ms |
MKL (2 CPUs)      |   552 ms      |  2718 ms |  96 ms |  267 ms |  423 ms |
MKL (8 CPUs)      |   525 ms      |  1679 ms |  60 ms |  137 ms |  197 ms |  
GotoBlas2 (1 CPU) |  2124 ms      |  4636 ms | 147 ms |  456 ms |  743 ms |
GotoBlas2 (2 CPUs)|  1560 ms      |  3278 ms | 116 ms |  295 ms |  460 ms |
GotoBlas2 (8 CPUs)|   741 ms      |  2914 ms |  82 ms |  262 ms |  192 ms |
Mac OS X (1 CPU)  |   948 ms      |  4339 ms | 151 ms |  318 ms |  566 ms |
Mac Server (1 CPU)|  1033 ms      |  3645 ms |  99 ms |  232 ms |  342 ms |

Installation

Installation of MKL included installing the complete Intel Compiler Suite which is pretty straight forward. However because of some bugs/issues configuring and compiling numpy with MKL support was a bit of a hassle.

GotoBlas2 is a small package which can be easily compiled as a shared library. However because of a bug you have to re-create the shared library after building it in order to use it with numpy.
In addition to this building it for multiple target plattform didn't work for some reason. So I had to create an .so file for each platform for which i want to have an optimized libgoto2.so file.

If you install numpy from Ubuntu's repository it will automatically install and configure numpy to use ATLAS. Installing ATLAS from source can take some time and requires some additional steps (fortran, etc).

If you install numpy on a Mac OS X machine with Fink or Mac Ports it will either configure numpy to use ATLAS or Apple's Accelerate Framework. You can check by either running ldd on the numpy.core._dotblas file or calling numpy.show_config().

Conclusions

MKL performs best closely followed by GotoBlas2.
In the eigenvalue test GotoBlas2 performs surprisingly worse than expected. Not sure why this is the case.
Apple's Accelerate Framework performs really good especially in single threaded mode (compared to the other BLAS implementations).

Both GotoBlas2 and MKL scale very well with number of threads. So if you have to deal with big matrices running it on multiple threads will help a lot.

In any case don't use the default netlib blas implementation because it is way too slow for any serious computational work.

On our cluster I also installed AMD's ACML and performance was similar to MKL and GotoBlas2. I don't have any numbers tough.

I personally would recommend to use GotoBlas2 because it's easier to install and it's free.

If you want to code in C++/C also check out Eigen3 which is supposed to outperform MKL/GotoBlas2 in some cases and is also pretty easy to use.

I've run your benchmark. There is no difference between C++ and numpy on my machine:

Do you think my approach is fair, or are there some unnecessary overheads I can avoid?

It seems fair due to there is no difference in results.

Would you expect that the result would show such a huge discrepancy between the c++ and python approach? Both are using shared objects for their calculations.

No.

Since I would rather use python for my program, what could I do to increase the performance when calling BLAS or LAPACK routines?

Make sure that numpy uses optimized version of BLAS/LAPACK libraries on your system.