Problem compiler error about figure/subfigure ' caption using latex IEEE ACCESS template

They provide a new command to handle the images in IEEE Access. I show you an example.

\Figure[!t]()[width=0.95\textwidth]{imageName}
   {Caption.\label{fig:label}}

This command puts the image using two columns or one column automatically. It depends on the figure's dimension. If it is lower than 50%, the figure is put in one column, else in two columns.

for plotting subfigures i used the code in the IEEE access template and it works. I included the following packages

\usepackage{cite}
\usepackage{amsmath,amssymb,amsfonts}
\usepackage{algorithmic}
\usepackage{graphicx}
\usepackage[caption=false]{subfig}
\usepackage{caption,setspace}
\captionsetup{font={sf,small,stretch=0.80},labelfont={bf,color=accessblue}}
\usepackage{textcomp}
\def\BibTeX{{\rm B\kern-.05em{\sc i\kern-.025em b}\kern-.08em
    T\kern-.1667em\lower.7ex\hbox{E}\kern-.125emX}}


\begin{figure*}[!t]
    \centering
    %\vspace*{-.02in}
    \subfloat[Performance comparison when x=t]{
        \hspace*{-.1in}
        \includegraphics[scale=0.33]{fig1.pdf}
        \hspace*{-.1in}
        \includegraphics[scale=0.33]{fig2.pdf}
        \label{p_D_req_100}
    }
    %   \vspace*{-.14in}
    \hfill
    \subfloat[Performance comparison when x=u]{
        \hspace*{-.1in}
        \includegraphics[scale=0.33]{fig3.pdf}
        \hspace*{-.1in}
        \includegraphics[scale=0.33]{fig4.pdf}
        \label{p_D_req_400}
    }
    %   \vspace*{-.14in}
    \hfill
    \subfloat[Performance comparison when x=z]{
        \hspace*{-.1in}
        \includegraphics[scale=0.33]{fig5.pdf}
        \hspace*{-.1in}
        \includegraphics[scale=0.33]{fig6.pdf}
        \label{p_D_req_1000}
    }
    \caption{the EE (left) and  xxxx  (right) of cat cat cat load.}
    \label{fig:p_graph}
\end{figure*}

If you are allowed to change the template, you can use the labelfont key in \captionsetup to set the color. Finding the latter took some digging in the code of the class. I also took the freedom to set the fonts according to the template (sf and bf).

The code:

% !TeX spellcheck = en_US
\documentclass{ieeeaccess}
\usepackage{cite}
\usepackage{amsmath,amssymb,amsfonts}
%\usepackage{algorithm}
%\usepackage{algorithmic}

\usepackage{graphicx}
\usepackage{subfigure}  % support sub-figure

% compiler error without following two lines
\usepackage{caption,setspace}
\captionsetup{font={sf,small,stretch=0.80},labelfont={bf,color=accessblue}}

\usepackage{textcomp}
\def\BibTeX{{\rm B\kern-.05em{\sc i\kern-.025em b}\kern-.08em
    T\kern-.1667em\lower.7ex\hbox{E}\kern-.125emX}}

\begin{document}

\begin{abstract}

hese instructions give you guidelines for preparing papers for 
IEEE Access. Use this document as a template if you are 
using \LaTeX. Otherwise, use this document as an 
instruction set. 
\end{abstract}

\begin{keywords}
Figure, Float, SubFigure

\end{keywords}

\titlepgskip=-15pt

\section{Introduction}
\label{sec:introduction}

\PARstart{T}{his} document is a template for \LaTeX. If you are 
reading a paper or PDF version of this document, please download the 
electronic file \ref{fig:universe}.

\begin{figure}[h!]
    \centering
    \includegraphics[scale=0.2]{example-image.png}
    \caption{Universe}
    \label{fig:universe}
\end{figure}

\Figure[h]()[scale=0.2]{example-image.png}{Universe}

\EOD

\end{document}