React Native Error: ENOSPC: System limit for number of file watchers reached

From the official document:

"Visual Studio Code is unable to watch for file changes in this large workspace" (error ENOSPC)

When you see this notification, it indicates that the VS Code file watcher is running out of handles because the workspace is large and contains many files. The current limit can be viewed by running:

cat /proc/sys/fs/inotify/max_user_watches

The limit can be increased to its maximum by editing

/etc/sysctl.conf

and adding this line to the end of the file:

fs.inotify.max_user_watches=524288

The new value can then be loaded in by running

sudo sysctl -p

Note that Arch Linux works a little differently, See Increasing the amount of inotify watchers for details.

While 524,288 is the maximum number of files that can be watched, if you're in an environment that is particularly memory constrained, you may wish to lower the number. Each file watch takes up 540 bytes (32-bit) or ~1kB (64-bit), so assuming that all 524,288 watches are consumed, that results in an upper bound of around 256MB (32-bit) or 512MB (64-bit).

Another option

is to exclude specific workspace directories from the VS Code file watcher with the files.watcherExclude setting. The default for files.watcherExclude excludes node_modules and some folders under .git, but you can add other directories that you don't want VS Code to track.

"files.watcherExclude": {
    "**/.git/objects/**": true,
    "**/.git/subtree-cache/**": true,
    "**/node_modules/*/**": true
  }

The meaning of this error is that the number of files monitored by the system has reached the limit!!

Result: The command executed failed! Or throw a warning (such as executing a react-native start VSCode)

Solution:

Modify the number of system monitoring files

Ubuntu

sudo gedit /etc/sysctl.conf

Add a line at the bottom

fs.inotify.max_user_watches=524288

Then save and exit!

sudo sysctl -p

to check it

Then it is solved!

Linux uses the inotify package to observe filesystem events, individual files or directories.

Since React / Angular hot-reloads and recompiles files on save it needs to keep track of all project's files. Increasing the inotify watch limit should hide the warning messages.

You could try editing

# insert the new value into the system config
echo fs.inotify.max_user_watches=524288 | sudo tee -a /etc/sysctl.conf && sudo sysctl -p

# check that the new value was applied
cat /proc/sys/fs/inotify/max_user_watches

# config variable name (not runnable)
fs.inotify.max_user_watches=524288

You can fix it, that increasing the amount of inotify watchers.

If you are not interested in the technical details and only want to get Listen to work:

• If you are running Debian, RedHat, or another similar Linux distribution, run the following in a terminal:

  $ echo fs.inotify.max_user_watches=524288 | sudo tee -a /etc/sysctl.conf && sudo sysctl -p

• If you are running ArchLinux, run the following command instead

  $ echo fs.inotify.max_user_watches=524288 | sudo tee /etc/sysctl.d/40-max-user-watches.conf && sudo sysctl --system

Then paste it in your terminal and press on enter to run it.

---

The Technical Details

Listen uses inotify by default on Linux to monitor directories for changes. It's not uncommon to encounter a system limit on the number of files you can monitor. For example, Ubuntu Lucid's (64bit) inotify limit is set to 8192.

You can get your current inotify file watch limit by executing:

$ cat /proc/sys/fs/inotify/max_user_watches

When this limit is not enough to monitor all files inside a directory, the limit must be increased for Listen to work properly.

You can set a new limit temporary with:

$ sudo sysctl fs.inotify.max_user_watches=524288
$ sudo sysctl -p

If you like to make your limit permanent, use:

$ echo fs.inotify.max_user_watches=524288 | sudo tee -a /etc/sysctl.conf
$ sudo sysctl -p

You may also need to pay attention to the values of max_queued_events and max_user_instances if listen keeps on complaining.