What does it mean to say "linux kernel is preemptive"?
Traditional unix kernels had a single lock, which was held by a thread while kernel code was running. Therefore no other kernel code could interrupt that thread.
This made designing the kernel easier, since you knew that while one thread using kernel resources, no other thread was. Therefore the different threads cannot mess up each others work.
In single processor systems this doesn't cause too many problems.
However in multiprocessor systems, you could have a situation where several threads on different processors or cores all wanted to run kernel code at the same time. This means that depending on the type of workload, you could have lots of processors, but all of them spend most of their time waiting for each other.
In Linux 2.6, the kernel resources were divided up into much smaller units, protected by individual locks, and the kernel code was reviewed to make sure that locks were only held while the corresponding resources were in use. So now different processors only have to wait for each other if they want access to the same resource (for example hardware resource).
Prior to Linux kernel version 2.5.4, Linux Kernel was not preemptive which means a process running in kernel mode cannot be moved out of processor until it itself leaves the processor or it starts waiting for some input output operation to get complete.
Generally a process in user mode can enter into kernel mode using system calls. Previously when the kernel was non-preemptive, a lower priority process could priority invert a higher priority process by denying it access to the processor by repeatedly calling system calls and remaining in the kernel mode. Even if the lower priority process' timeslice expired, it would continue running until it completed its work in the kernel or voluntarily relinquished control. If the higher priority process waiting to run is a text editor in which the user is typing or an MP3 player ready to refill its audio buffer, the result is poor interactive performance. This way non-preemptive kernel was a major drawback at that time.
Imagine the simple view of preemptive multi-tasking. We have two user tasks, both of which are running all the time without using any I/O or performing kernel calls. Those two tasks don't have to do anything special to be able to run on a multi-tasking operating system. The kernel, typically based on a timer interrupt, simply decides that it's time for one task to pause to let another one run. The task in question is completely unaware that anything happened.
However, most tasks make occasional requests of the kernel via syscalls. When this happens, the same user context exists, but the CPU is running kernel code on behalf of that task.
Older Linux kernels would never allow preemption of a task while it was busy running kernel code. (Note that I/O operations always voluntarily re-schedule. I'm talking about a case where the kernel code has some CPU-intensive operation like sorting a list.)
If the system allows that task to be preempted while it is running kernel code, then we have what is called a "preemptive kernel." Such a system is immune to unpredictable delays that can be encountered during syscalls, so it might be better suited for embedded or real-time tasks.
For example, if on a particular CPU there are two tasks available, and one takes a syscall that takes 5ms to complete, and the other is an MP3 player application that needs to feed the audio pipe every 2ms, you might hear stuttering audio.
The argument against preemption is that all kernel code that might be called in task context must be able to survive preemption-- there's a lot of poor device driver code, for example, that might be better off if it's always able to complete an operation before allowing some other task to run on that processor. (With multi-processor systems the rule rather than the exception these days, all kernel code must be re-entrant, so that argument isn't as relevant today.) Additionally, if the same goal could be met by improving the syscalls with bad latency, perhaps preemption is unnecessary.
A compromise is CONFIG_PREEMPT_VOLUNTARY, which allows a task-switch at certain points inside the kernel, but not everywhere. If there are only a small number of places where kernel code might get bogged down, this is a cheap way of reducing latency while keeping the complexity manageable.
The preemption allows the kernel to give the IMPRESSION of parallelism: you've got only one processor (let's say a decade ago), but you feel like all your processes are running simulaneously. That's because the kernel preempts (ie, take the execution out of) the execution from one process to give it to the next one (maybe according to their priority).
EDIT Not preemptive kernels wait for processes to give back the hand (ie, during syscalls), so if your process computes a lot of data and doesn't call any kind of yield function, the other processes won't be able to execute to execute their calls. Such systems are said to be cooperative because they ask for the cooperation of the processes to ensure the equity of the execution time
EDIT 2 The main goal of preemption is to improve the reactivity of the system among multiple tasks, so that's good for end-users, whereas on the other-hand, servers want to achieve the highest througput, so they don't need it: (from the Linux kernel configuration)
- Preemptible kernel (low-latency desktop)
- Voluntary kernel preemption (desktop)
- No forced preemption (server)